Search
English
All Categories
    Menu Close

    WEO12832L#NP3N00000-FC

    PMOLED 2.22" Graphic 128x32, Yellow color, COG, 3V, Interface 6800,8080,SPI,I2C, SH1106 IC, Glare (FPC per ZIF Connector)
    Manufacturer: Winstar
    SKU: WEO12832L#NP3N00000-FC

    Accessory kit

    PRICE BREAKS
    Quantity
    1+
    5+
    10+
    25+
    Price
    €14.40
    €13.00
    €12.20
    €11.90

    For quantities above 49pcs pls send your enquiry to [email protected] or call +39 0332 1888005

    Availability: In stock
    €14.40 excl tax
    i h

    DRAWING

     

    SPECIFICATIONS

    Interface Pin Function

    No.SymbolFunction
    1 N.C.(GND) No connection.
    2~3 VSS Ground.
    4 N.C. No connection.
    5 VDD1 Power supply input.
    6 IM1
     8080I2C68004-SPI
    IM1 1 1 0 0
    IM2 1 0 1 0
    These are the MPU interface mode select pads.
    7 IM2
    8 ___
    CS
    This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
    9 ___
    RES
    This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
    10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
    A0 = “H”: the inputs at D0 to D7 are treated as display data.
    A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
    In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
    11 ___
    WR
    This is a MPU interface input pad.
    When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
    When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
    When R/W = “H”: Read.
    When R/W = “L”: Write.
    12    ___
    E/RD
    This is a MPU interface input pad.
    When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
    When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
    When RD = “H”: Enable.
    When RD = “L”: Disable.
    13~20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
    When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
    When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
    21 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
    22 VCOMH This is a pad for the voltage output high level for common signals.
    A capacitor should be connected between this pad and VSS.
    23 VPP OLED panel power supply. Generated by internal charge pump.
    Connect to capacitor. It could be supplied externally.
    24 NC(GND) No connection.

     

    Mechanical Data

    ItemDimensionUnit
    Dot Matrix 128 × 32 Dots -
    Module dimension 62.0 × 24.0 × 2.17 mm
    Active Area 55.016 × 13.096 mm
    Pixel Size 0.406 × 0.386 mm
    Pixel Pitch 0.43 × 0.41 mm
    Display Mode Passive Matrix
    Display Color Monochrome
    Drive Duty 1/32 Duty
    IC SH1106
    Interface 6800,8080,4-Wire SPI,I2C
    Size 2.23 inch

     

    Absolute Maximum Ratings

    ParameterSymbolMinMaxUnit
    Supply Voltage For Logic VDD1-VSS -0.3 3.6 V
    Supply Voltage for Display VPP -0.3 14.5 V
    Operating Temperature TOP -40 +80 °C
    Storage Temperature TSTG -40 +85 °C

     

    Electronical Characteristics

    DC Electrical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage for Logic VDD1 - 1.65 3.0 3.3 V
    Supply Voltage for Display VPP - 6.4 12.0 12.5 V
    Input High Volt. VIH - 0.8XVDD1 - VDD1 V
    Input Low Volt. VIL - VSS - 0.2xVDD1 V
    Output High Volt. VOH - 0.8xVDD1 - VDD1 V
    Output Low Volt. VOL - VSS - 0.2xVDD1 V
    Display 50% Pixel On IPP VPP=12V - 15 30 mA
     

    Products specifications
    Size 2.22"
    Resolution 128x32
    Active Area (mm) 55.01x13.09
    Dot Size 0.40x0.38
    Polarizer Glare
    Color Yellow
    Power supply 3V
    Display Interface 6800/8080/SPI/I2C
    Display IC SH1106
    Constructive Structure COG
    Frame No
    Touch Panel No touch
    O. Temperature (°C) -40~80
    Data Connection FPC for ZIF Connector
    Pin Nr. 24
    Pin Pitch 0.5mm
    Preferred - Not Preferred Preferred
    *
    *
    *
    *
    Only registered users can write reviews