Search
English
All Categories
    Menu Close

    WL0F00101000JGFAASA00-FC

    TFT 10.1" 1024x600, UART interface & GPIO Support, 400cd/m², Wide View Angle (IPS), Capacitive touch panel (GG)
    Manufacturer: Winstar
    SKU: WL0F00101000JGFAASA00-FC

    Accessory kit

    PRICE BREAKS
    Quantity
    1+
    5+
    10+
    Price
    €125.70
    €113.10
    €106.30

    For quantities above 24pcs pls send your enquiry to [email protected] or call +39 0332 1888005

    Availability: In stock
    €125.70 excl tax
    i h

    DESCRIPTION

    Below are the features of this 10.1 inches Smart Display (UART series):

    1. +12V power supply input, the power consumption is around &W.
    2. Self-testing after booting function.
    3. UART communication interface.
    4. Supports UART protocol, default baud rate at 115200Kbps.
    5. Built in flash memory, store the font and Object Dictionary Data.
    6. Support capacitive touch panel (CTP).
    7. Embedded buzzer controlled by Master Device.
    8. Demo set HOST can be used on multiple platforms, such as Computer (with USB to UART Dongle), MCU, Raspberry Pi (with PiCAN2).
    9. GPIO PIN support.

      

    DRAWING

     

    SPECIFICATIONS

    General Information

    ItemStandard ValueUnit
    Operating voltage 8~28V dynamic Vdc
    Communication Interface UART --
    MCU STM32F746 N/A
    Flash ROM 16 MB
    LCD display size 10.1 inch
    Dot Matrix 1024 x RGB x 600(TFT) dot
    Module dimension 235(W) x 143(H) x 23.2(D) mm
    Active area 222.72(H) x 125.28(V) mm
    Pixel pitch 0.2175(W) x 0.2088(H) mm
    Brightness Min: 300; Typ: 400 cd/m2
    LCD type TFT, Normally White
    View Direction 85/85/85/85
    Aspect Ratio 16:9
    With / Without TP With CTP
    Surface Glare


    Absolute Maximum Ratings

    ItemSymbolMinTypMaxUnit
    Operating Temperature TOP -20 - +70 ℃
    Storage Temperature TST -30 - +80 ℃

     

    Electrical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage VCC - 8 12 28 V
    Supply LCM current I(mA) - - 530 - mA 

     

    BOM

    ItemDescription
    LCM WF101-­1024600JL#0P8-­FC
    PCBA SV10010R100JB00N0105

     

    Interface Pin Function

    CON1 definition

    PinSymbolFunctionRemark
    1 +12V Power supply 12V input Input
    2 GND Power supply GND input Input
    3 Reserve - -
    4 Reserve - -
    5 GND Power supply GND input GND
    6 GND Power supply GND input GND
    7 Reserve - -
    8 Reserve - -
    9 NC - -
    10 UART_RX UART RX interface I/O
    11 UART_TX UART TX interface I/O
    12 GND Power supply GND input GND
    13 +12V Power supply 12V input Input
    14 NC - -
    15 NC - -
    16 GND Power supply GND input Input


    CON2 definition

    PinSymbolFunctionRemark
    1 VDD3V 3.3V power for JTAG interface Output
    2 JTAG_SWCLK CLK pin for JTAG interface Input
    3 GND GND for JTAG interface Output
    4 JTAG_SWDIO Data pin for JTAG interface I/O
    5 NRST Reset pin for JTAG interface Input
    6 GND GND Output
    7 Wkup/IO_8 (PA0) for system Resume from suspend (Reserve) WKup,ADC,Timer,Event,I/O
    8 /RST

    Reset (active Low)

    I
    9 IO_0 ADC,DAC,Timer,Event,I/O PA5
    10 IO_1 ADC,Timer,Event,I/O PA6
    11 IO_2 ADC,Timer,Event,I/O PA7
    12 IO_3 RST,Timer,Event,I/O PA8
    13 IO_4 RST,Timer,Event,I/O PC13
    14 IO_5 ADC,Timer,Event,I/O PB11
    15 IO_6 RST,Timer,Event,I/O PA15
    16 IO_7 RST,ADC,Event,I/O PD11

     

    Display Usage

    Functional description

    Smart Display can be used to display the coordinate, status and data information provided by the connected HOST device. Customers can configure the position coordinates they want to display in normal operation mode.

    The Display is designed to be easily connected to a controller network, and to use the register type of Holding Register.

    Splash Screen

    The default splash image is shown below.

    This product is produced as a generic product. If you require a custom splash image for your application, contact us to discuss.


    Default Selection

    Press the preferred application and hold for 3 seconds for the first time power on.
     

    Winstar's Smart Display Default Selection


    Acquisition of Displayed Data

    Smart Display uses the Modbus protocol to get and send the data.

    On Config mode, customers can set the coordinates or type of objects; On Display mode, customers can send and get data of objects.

    Configuring the Display

    Winstar Smart Display RS-485 series offers an out-of-the-box Modbus development experience that will lower customers' development costs and speed time-to-market expectations.

    The Smart Display can use wide-temperature are designed to support control applications in harsh operating conditions, which designed to be connected to a variety of different situation combinations, such as automotive, marine, power generation and oil-and-gas.

    The Smart Display comes with standard UI objects to get customers project off the ground quickly. If customers need custom UI objects support, our engineers are here to help. Send over your contents in PNG/JPG format, we will send over a new set of UI objects within 3~5 working days.

    The Smart Display is defined as a slave device, which is controlled by master device via RS485 bus command to render display content on the display screen and return touch event data with protocol objects.

    Example Screen Layout (Industry application)

    The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in an industry application situation.

    Example Screen Layout (Vehicle automotive)

    The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in a vehicle automotive situation.


    Example Screen Layout (Medical application)

    The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in a Medical application situation.

    Products specifications
    Size 10.1"
    Resolution 1024x600
    Active Area (mm) 222.72x125.28
    Color Full Color
    Power supply 12V
    Display Interface UART + GPIO
    View Angle IPS
    Frame Yes
    Touch Panel Capacitive
    O. Temperature (°C) -20~70
    Preferred - Not Preferred Preferred
    *
    *
    *
    *
    Only registered users can write reviews