Cerca
Italiano
Catalogo
    Menu Chiudi

    WO12864-84ID3#FC

    Graphic LCD 2.9" 128x64, B/L white, STN blue neg, Transmissive, COG, 3.3V, Interface 6800/8080/SPI, 6 O'clock (IC ST7565P)
    Brand: Winstar
    Cod.: WO12864-84ID3#FC

    Kit accessori

    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    25+
    Prezzo
    €16,90
    €15,20
    €14,30
    €14,00

    Per quantità maggiori di 49pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Disponibile
    €16,90 IVA esclusa
    i h

    DRAWING

     

    SPECIFICATIONS

    Interface Pin Function

    Pin No.SymbolLevelDescription
    1 /CS1 I The chip select signal
    2 /RES I When RES is set to “L”, the setting are initialized.
    3 A0 I This is connect to the least significant bit of the normal MPU address bus, and it determines whether the data bits are data or command.
    A0 = “H”: Indicates that D0 to D7 are display data.
    A0 = “L”: Indicates that D0 to D7 are control data.
    4 /WR(R/W) I • When connected to 8080 series MPU, this pin is treated as the “/WR” signal of the 8080 MPU and is LOW-active.
    The signals on the data bus are latched at the rising edge of the /WR signal.
    • When connected to 6800 series MPU, this pin is treated as the “R/W” signal of the 6800 MPU and decides the access type :
    When R/W = “H”: Read.
    When R/W = “L”: Write.
    5 /RD(E) I • When connected to 8080 series MPU, this pin is treated as the “/RD” signal of the 8080 MPU and is LOW-active.
    The data bus is in an output status when this signal is “L”.
    • When connected to 6800 series MPU, this pin is treated as the “E” signal of the 6800 MPU and is HIGH-active.
    This is the enable clock input terminal of the 6800 Series MPU.
    6~13 D0~D7 I/O Data bus line
    14 VDD Power
    Supply
    Power supply
    15 VSS Power
    Supply
    Ground
    16 VOUT O DC/DC voltage converter. Connect a capacitor between this terminal and vss or VDD
    17 CAP5+ O DC/DC voltage converter
    18 CAP3+
    19 CAP1-
    20 CAP1+
    21 CAP2+
    22 CAP2-
    23 CAP4+
    24 VRS Power
    Supply
    This is the internal-output VREG power supply for the LCD power supply voltage
    regulator.
    25 V4 Power
    Supply
    This is a multi-level power supply for the liquid crystal drive.
    26 V3
    27 V2
    28 V1
    29 V0
    30 VR I Output voltage regulator terminal. Provides the voltage between VSS and V0 through a resistive voltage divider.
    IRS = “L” : the V0 voltage regulator internal resistors are not used.
    IRS = “H” : the V0 voltage regulator internal resistors are used.
    31 C86 I This is the MPU interface selection pin.
    C86 = “H”: 6800 Series MPU interface.
    C86 = “L”: 8080 Series MPU interface
    32 P/S I This is the parallel data input/serial data input switch terminal.
    P/S = “H”: Parallel data input.
    P/S = “L”: Serial data input.
    The following applies depending on the P/S status:
    P/S Data/Command Data Read/Write Serial Clock
    "H" A0 D0 to D7 /RD,/WR X
    "L" A0 SI(D7) Write only SCL(D6)
    When P/S = “L”, D0 to D5 fixed  “H”.
    /RD (E) and /WR (R/W) are fixed to either “H” or “L”.
    With serial data input, It is impossible read data from RAM
    33 /HPM I This is the power control terminal for the power supply circuit for liquid crystal drive.
    /HPM = “H”: Normal mode
    /HPM = “L”: High power mode
    34 IRS I This terminal selects the resistors for the V0 voltage level adjustment.
    IRS = “H”: Use the internal resistors
    IRS = “L”: Do not use the internal resistors. The V0 voltage level is
    regulated by an external resistive voltage divider attached to the VR terminal

     

    Mechanical Data

    ItemDimensionUnit
    Number of Dots 128 x 64 -
    Module dimension 80.0 x 54.0 x 9.5 mm
    View area 70.7 x 38.8 mm
    Active area 66.52 x 33.24 mm
    Dot size 0.48 x 0.48 mm
    Dot pitch 0.52 x 0.52 mm
    Duty 1/64 , 1/9 Bias
    Backlight Type LED
    IC ST7565P
    Interface 6800/8080/4-Line SPI

     

    Absolute Maximum Ratings

    ItemSymbolMinTypMaxUnit
    Operating Temperature TOP -20 - +70 ℃
    Storage Temperature TST -30 - +80 ℃
    Power Supply Voltage VDD -0.3 - 3.6 V
    Power supply voltage (VDD standard) V0,VOUT -0.3 - 14.5 V
    Power supply voltage (VDD standard) V1,V2,V3,V4 -0.3 - V0+0.3 V

     

    Electrical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage For Logic VDD-VSS - 2.7 - 3.3 V
    Supply Voltage For LCM V0-VSS Ta=-20℃
    Ta=25℃
    Ta=70℃
    10.0
    9.8
    9.6
    10.2
    10.0
    9.8
    10.4
    10.2
    10.0
    V
    V
    V
    Input High Volt. VIH - 0.8 VDD - VDD V
    Input Low Volt. VIL - VSS - 0.2VDD V
    Output High Volt. VOH - 0.8VDD - VDD V
    Output Low Volt. VOL - VSS - 0.2VDD V
    Supply Current(No include LED Backlight) IDD - - 0.6 1.0 mA
    Specifiche di prodotto
    Size 2.9"
    Resolution 128x64
    Active Area (mm) 66.52x33.24
    Dot Size 0.48x0.48
    B/L color, LCD type B/L white, STN blue neg
    Power supply 3.3V
    Display Interface 6800/8080/SPI
    Display IC ST7565P
    Constructive Structure COG
    View Angle 6H
    Frame No
    Touch Panel No touch
    O. Temperature (°C) -20~70
    Data Connection FPC for ZIF Connector
    Pin Nr. 34
    Pin Pitch 0.5mm
    Preferred - Not Preferred Not Preferred
    You are running a Trial version of Nop Attachments
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni