Cerca
Italiano
Catalogo
    Menu Chiudi
    PMOLED 0.49" Graphic 64x32, Yellow color, COG, 3V, Interface I2C, Glare (FPC per Soldering)
    Brand: Winstar
    Cod.: WEO6432L#A00-FC
    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    25+
    Prezzo
    €4,70
    €4,20
    €4,00
    €3,90

    Per quantità maggiori di 49pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Il prodotto non può essere aggiunto al carrello. Prego verificare con FC la futura disponibilità
    €4,70 IVA esclusa
    i h

    DESCRIPTION

    0.49 inch passive matrix micro OLED display module which is made of 64x32 dots. It has module dimension of 14.5x 11.6 x 1.26 mm and Active Area size 11.18 × 5.58 mm. OLED micro display is built in with SSD1306 IC, it supports I2C interface, 3V power supply. COG structure OLED display which is ultra thin and no need of backlight (self emitting); it's lightweight and low power consumption. This 0.49 inch small sized OLED module is suitable for wearable device, mp3, portable device, personal care appliance, voice recorder pen, health device, etc.  Operating temperatures from -40℃ to +80℃; storage temperatures range from -40℃ to +85℃.

     

    DRAWING

     
     

    SPECIFICATIONS

     

    Interface Pin Function

    No.SymbolFunction
    1 C2N Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
    2 C2P
    3 C1P
    4 C1N
    5 VBAT Power Supply for DC/DC Converter Circuit
    This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
    6 NC No connection.
    7 VSS Ground of Logic Circuit
    This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
    8 VDD Power Supply for Logic
    This is a voltage supply pin. It must be connected to external source.
    9 RES# Power Reset for Controller and Driver
    This pin is reset signal input. When the pin is low, initialization of the chip is executed.
    10 SCL Host Data Input/Output Bus
    When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.
    11 SDA
    12 IREF Current Reference for Brightness Adjustment
    This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
    13 VCOMH Voltage Output High Level for COM Signal
    This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
    14 VCC Power Supply for OEL Panel
    This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

     

    Mechanical Data

    ItemDimensionUnit
    Dot Matrix 64 × 32 Dots
    Module dimension 14.5 × 11.6 × 1.26 mm
    Active Area 11.18 × 5.58 mm
    Pixel Size 0.153 × 0.153 mm
    Pixel Pitch 0.175 × 0.175 mm
    Display Mode Passive Matrix
    Display Color Monochrome
    Drive Duty 1/32 Duty
    IC SSD1306

     

    Absolute Maximum Ratings

    ParameterSymbolMinMaxUnit
    Supply Voltage for Logic VDD 0 4 V
    Supply Voltage for Display VCC 0 15 V
    Operating Temperature TOP -40 +80 °C
    Storage Temperature TSTG -40 +80 °C

     

    Electronical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage for Logic  VDD - 2.8 3 3.3 V
    Supply Voltage for Display  VCC - 7 7.5 7.8 V
    Input High Volt. VIH - 0.8×VDD - VDDIO V
    Input Low Volt. VIL - 0 - 0.2×VDD V
    Output High Volt. VOH - 0.9×VDD - VDDIO V
    Output Low Volt. VOL - 0 - 0.1×VDD V
    50% Check Board operating Current ICC VCC=7.5V - 5 20 mA


    Specifiche di prodotto
    Size 0.49"
    Resolution 64x32
    Active Area (mm) 11.18x5.58
    Dot Size 0.15x0.15
    Polarizer Glare
    Color Yellow
    Power supply 3V
    Display Interface I2C
    Display IC SSD1306BZ
    Constructive Structure COG
    Frame No
    Touch Panel No touch
    O. Temperature (°C) -40~80
    Data Connection FPC for Soldering
    Pin Nr. 14
    Pin Pitch 0.7mm
    Preferred - Not Preferred Not Preferred
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni