Cerca
Italiano
Catalogo
    Menu Chiudi

    WEO25664W#EP3N00000-FC

    PMOLED 3.55" Graphic 256x64, White color, COG, 3V, Interface 6800, 8080, SPI, I2C, Glare
    Brand: Winstar
    Cod.: WEO25664W#EP3N00000-FC

    Kit accessori

    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    Prezzo
    €30,80
    €27,70
    €26,00

    Per quantità maggiori di 24pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Il prodotto non può essere aggiunto al carrello. Prego verificare con FC la futura disponibilità
    €30,80 IVA esclusa
    i h

    DESCRIPTION

    The WEO25664W#EP3N00000-FC is a 3.55-inch COG Graphic OLED display with a 256x64 dot matrix, driven by the SSD1363 controller IC. It supports 4-bit (16-level) grayscale and provides multiple interface options: 6800/8080 parallel, 3-wire/4-wire SPI, and I2C. The inclusion of I2C offers additional flexibility for designs that prioritize simpler communication and reduced power consumption.

    This model feature high contrast, wide viewing angles, and a 1/64 duty cycle for efficient power management. The WEO25664W#EP3N00000-FC operates with a 3.3V logic supply and 16V display driving voltage, with a typical current consumption of 35mA at 50% checkerboard pattern (VCC=16V).

    Designed for stable, long-term display in applications such as medical devices, control panels, and self-checkout systems, the WEO25664W#EP3N00000-FC operates within a temperature range of –40°C to +80°C, with a storage temperature range from –40°C to +85°C.

     

    DRAWING

    SPECIFICATIONS

    Mechanical Data

    ItemDimensionUnit
    Dot Matrix 256 x 64 Dots -
    Module dimension 99.2 × 33.5 × 2.01 mm
    Active Area 87.52 × 21.28 mm
    Pixel Size 0.312 × 0.303 mm
    Pixel Pitch 0.342 × 0.333 mm
    Display Mode Passive Matrix
    Display Color Monochrome
    Drive Duty 1/64 Duty
    Gray Scale 4 bits
    IC SSD1363
    Interface 6800,8080,4-Wire SPI,I2C
    Size 3.55 inch

     

    Absolute Maximum Ratings

    ParameterSymbolMinMaxUnit
    Supply Voltage VDD -0.3 4.0 V
    Supply Voltage VCC -0.5 19.0 V
    Operating Temperature TOP -40 +80 °C
    Storage Temperature TSTG -40 +85 °C

     

    Electronical Characteristics

    DC Electrical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Low voltage power supply,
    power Supply for I/O pins
    VDD - 1.65 3.0 3.3 V
    Operating Voltage VCC - 8.0 16.0 16.5 V
    High Level Input VIH - 0.8×VDD - VDD V
    Low Level Input VIL - 0 - 0.2×VDD V
    High Level Output VOH - 0.9×VDD - VDD V
    Low Level Output VOL - 0 - 0.1×VDD V
    Display 50% Pixel on ICC VCC =16V - 30 45 mA

     

    Interface Pin Function

    Pin NumberSymbolFunction
    1 ESD_GND ESD Ground pin
    2 VSS Ground pin. It must be connected to external ground.
    3 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
    A capacitor should be connected between this pin and VSS.
    4 VCOMH COM signal deselected voltage level.
    A capacitor should be connected between this pin and VSS.
    5 VLSS Analog system ground pin. It must be connected to external ground.
    6 D7 These pins are bi-directional data bus connecting to the MCU data bus.
    Unused pins are recommended to tie LOW.
    When serial interface mode is selected, D2, D1 should be tied together as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
    When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
    7 D6
    8 D5
    9 D4
    10 D3
    11 D2
    12 D1
    13 D0
    14 E(RD#) This pin is MCU interface input.
    When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
    Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
    When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
    When serial or I2C interface is selected, this pin must be connected to VSS.
    15 R/W# (WR#) This pin is read / write control input pin connecting to the MCU interface.
    When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
    When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
    When serial or I2C interface is selected, this pin must be connected to VSS.
    16 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select.
     8080I2C68004-wire SPI
    BS1 1 1 0 0
    BS2 1 0 1 0
    Note:
    (1) 0 is connected to VSS
    (2) 1 is connected to VDD
    17 BS2

    18
    D/C# This pin is Data/Command control pin connecting to the MCU.
    When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
    When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
    In I2C mode, this pin acts as SA0 for slave address selection.
    19 CS# This pin is the chip select input connecting to the MCU.
    The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
    20 RES# This pin is reset signal input.
    When the pin is pulled LOW, initialization of the chip is executed.
    Keep this pin pull HIGH during normal operation.
    21 FR This pin outputs RAM write synchronization signal. Proper timing between MCU data writing and frame display timing can be achieved to prevent tearing effect.
    It should be kept NC if it is not used.
    22 IREF This pin is the segment output current reference pin.
    IREF is supplied externally. A resistor should be connected between this pin and VSS to maintain the current around 10uA.
    It should be kept floating when internal IREF is chosen by command setting.
    23~24 NC This is dummy pin. It should be kept NC.
    25 VP This pin is the segment pre-charge voltage reference pin.
    A capacitor can be connected between this pin and VSS to improve visual performance. It can also be float per application.
    No external power supply is allowed to connect to this pin.
    26 VDD Power supply pin for core logic operation. A capacitor should be connected between this pin and VSS.
    27 VSL This is segment voltage (output low level) reference pin.
    This pin has to be connected with resistor and diode to ground (details depends on application).
    28 VLSS Analog system ground pin. It must be connected to external ground.
    29 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
    A capacitor should be connected between this pin and VSS.
    30 ESD_GND ESD Ground pin
     
    Specifiche di prodotto
    Size 3.55"
    Resolution 256x64
    Active Area (mm) 87.52x21.28
    Dot Size 0.31x0.30
    Polarizer Glare
    Color White
    Power supply 3V
    Display Interface 6800/8080/SPI/I2C
    Display IC SSD1363
    Constructive Structure COG
    Frame No
    Touch Panel No touch
    O. Temperature (°C) -40~80
    Data Connection FPC for ZIF Connector
    Pin Nr. 30
    Pin Pitch 0.5mm
    Preferred - Not Preferred Preferred
    You are running a Trial version of Nop Attachments
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni