Cerca
Italiano
Catalogo
    Menu Chiudi
    PMOLED 2.08" Graphic 256x64, Yellow color, COG, 3V, Interface 6800,8080,SPI, I2C, Anti-glare (FPC per ZIF)
    Brand: Winstar
    Cod.: WEO25664L#A00-FC
    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    25+
    Prezzo
    €14,70
    €13,20
    €12,50
    €12,20

    Per quantità maggiori di 49pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Il prodotto non può essere aggiunto al carrello. Prego verificare con FC la futura disponibilità
    €14,70 IVA esclusa
    i h

    DESCRIPTION

    Graphic OLED display COG (chip on glass) type which is made of 256x64 pixels, diagonal size 2.08 inch. It is built in with SSD1362 driver IC; it can communicate via 6800/8080 8-bit parallel, I2C, 3-Wire and 4-Wire SPI interface; it supports 4 bits grayscale image. The supply voltage for logic is 3V supply, 1/64 duty cycle, display with 50% check board current is 15mA@12Vcc (typical value). This OLED module can be operating at temperatures from -40℃ to +80℃; its storage temperatures range from -40℃ to +85℃.

    It is a COG structure OLED module which is ultra thin 1.61 mm; lightweight and low power consumption. It is suitable for smart home application, meter device, personal care appliance, health device, etc.

     

    DRAWING

     

     

    SPECIFICATIONS

    Interface Pin Function

    No.SymbolFunction
    1 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
    2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
    3 VP This pin is the segment pre-charge voltage reference pin.
    A capacitor should be connected between this pin and VSS.
    No external power supply is allowed to connect to this pin.
    4 VCOMH COM signal deselected voltage level.
    A capacitor should be connected between this pin and VSS.
    No external power supply is allowed to connect to this pin.
    5 VDD Power supply for core logic operation.
    VDD can be supplied externally (within the range of 1.65V to 2.6V) or regulated internally from VCI when VCI is >2.6V.
    A capacitor should be connected between VDD and VSS under all circumstances.
    6 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
    7 IREF This pin is the segment output current reference pin.
    When external IREF is used, a resistor should be connected between this pin and VSS to maintain current of around 18.75uA.
    When internal IREF is used, this pin should be kept NC.
    8 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
    9 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
    10 VSS Ground pin. It must be connected to external ground.
    11 VSS Ground pin. It must be connected to external ground.
    12 VCI Low voltage power supply.
    VCI must always be equal to or higher than VDD and VDDIO.
    13 BS0 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1, BS0 are pin select.
    BS[2:0]Interface
    000 4 line SPI
    001 3 line SPI
    110 8-bit 8080 parallel
    100 8-bit 6800 parallel
    010 I2C
    Note  (1) 0 is connected to VSS  (2) 1 is connected to VCI
    14 BS1
    16 BS2
    15 VCI Low voltage power supply.
    VCI must always be equal to or higher than VDD and VDDIO.
    17 CS This pin is the chip select input connecting to the MCU.
    The chip is enabled for MCU communication only when CS is pulled LOW (active LOW).
    In I2C mode, this pin must be connected to VSS.
    18 RES This pin is reset signal input.
    When the pin is pulled LOW, initialization of the chip is executed.
    Keep this pin pull HIGH during normal operation.
    19 D/C This pin is Data/Command control pin connecting to the MCU.
    When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
    When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
    In I2C mode, this pin acts as SA0 for slave address selection.
    When 3-wire serial interface is selected, this pin must be connected to VSS.
    20 R/W This pin is read / write control input pin connecting to the MCU interface.
    When 6800 interface mode is selected, this pin will be used as Read/Write (R/W) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
    When 8080 interface mode is selected, this pin will be the Write (WR) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
    When serial or I2C interface is selected, this pin must be connected to VSS.
    21 RD This pin is MCU interface input.
    When 6800 interface mode is selected, this pin will be used as the Enable signal.
    Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
    When 8080 interface mode is selected, this pin receives the Read (RD) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
    When serial or I2C interface is selected, this pin must be connected to VSS.
    22 D0 These pins are bi-directional data bus connecting to the MCU data bus.
    Unused pins are recommended to tie LOW.
    When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID.
    When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
    23 D1
    24 D2
    25 D3
    26 D4
    26 D5
    28 D6
    29 D7
    30 NC These pins are reserved. Nothing should be connected to these pins, nor are they connected together.
    31 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.

     

    Mechanical Data

    ItemDimensionUnit
    Dot Matrix 256 x 64 Dots -
    Module dimension 60.5 x 19.0 x 1.61 mm
    Active Area 51.18 x 12.78 mm
    Pixel Size 0.18 x 0.18 mm
    Pixel Pitch 0.2 x 0.2 mm
    Display Mode Passive Matrix
    Display Color Monochrome
    Drive Duty 1/64 Duty
    Gray Scale 4 Bits
    IC SSD1362
    Interface 3-Wire and 4-Wire SPI, I2C, 6800, 8080
    Size 2.08 inch

     

    Absolute Maximum Ratings

    ParameterSymbolMinMaxUnit
    Supply Voltage for Operation VCI -0.5 5.5 V
    Supply Voltage for Logic VDD -0.5 2.75 V
    Supply Voltage for Display VCC -0.5 21 V
    Operating Temperature TOP -40 +80 °C
    Storage Temperature TSTG -40 +85 °C

     

    Electronical Characteristics

    DC Electrical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage for Logic VCI - 2.8 3.0 3.3 V
    Supply Voltage for Display VCC - 11.5 12 12.5 V
    Input High Volt. VIH - 0.8×VCI - VCI V
    Input Low Volt. VIL - VSS - 0.2×VCI V
    Output High Volt. VOH - 0.9×VCI - VCI V
    Output Low Volt. VOL - VSS - 0.1×VCI V
    50% Check Board operating Current ICC VCC=12V - 15 30 mA

     

    FPC options

    DrawingFPC LengthPINPitchZIF or HOTBAR FPCInterfaceFPC No.Create Date
    FPC2070002401XXXXX02_WEO025664ALAP3N00H00 23 24 0.7 HOTBAR 3-Wire and 4-Wire SPI, I2C, 6800, 8080 FPC2070002401XXXXX02 20180611
    21 31 0.3 ZIF 3-Wire and 4-Wire SPI, I2C, 6800, 8080 FPC2030003111XXXXX02 20171107


    Specifiche di prodotto
    Size 2.08"
    Resolution 256x64
    Active Area (mm) 51.15x12.78
    Dot Size 0.18x0.18
    Polarizer Anti-glare
    Color Yellow
    Power supply 3V
    Display Interface 6800/8080/SPI/I2C
    Display IC SSD1362Z
    Constructive Structure COG
    Frame No
    Touch Panel No touch
    O. Temperature (°C) -40~80
    Data Connection FPC for ZIF Connector
    Pin Nr. 31
    Pin Pitch 0.3mm
    Preferred - Not Preferred Preferred
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni