Cerca
Italiano
Catalogo
    Menu Chiudi
    PMOLED 0.96" Graphic 128x64, Sky Blue color, COG, 3V, Interface 6800,8080,SPI,I2C, Anti-glare (FPC per Soldering)
    Brand: Winstar
    Cod.: WEO12864S#C01-FC
    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    25+
    Prezzo
    €9,60
    €8,70
    €8,10
    €7,90

    Per quantità maggiori di 49pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Disponibile
    €9,60 IVA esclusa
    i h

    MOQ

    After sample PO, MP MOQ 1000pcs.

     

    DESCRIPTION

    ZIF FPC version of Graphic OLED display made of 128x64 pixels, diagonal size only 0.96 inch. It is built in with SH1106 controller IC and it communicates via 6800/8080 8-bit parallel, I2C and 4-wire SPI interface, 1/64 duty cycle.

    Small COG OLED display which is very thin; lightweight and low power consumption.  It is suitable for handheld instruments, smart meters, voice recorder, wearable device, IoT, etc.  Operating temperatures from -40℃ to +80℃; storage temperatures range from -40℃ to +85℃.

     

    DRAWING

    WEO012864C-ZIF - Winstar Display



    SPECIFICATIONS

     

    Interface Pin Function

    No.SymbolFunction
    1 NC No connection
    2 C1N Connect to charge pump capacitor.
    These pins are not used and should be disconnected when Vpp is supplied externally.
    3 C1P
    4 C2P Connect to charge pump capacitor.
    These pins are not used and should be disconnected when Vpp is supplied externally.
    5 C2N
    6 VDD2 3.0 – 4.7V power supply pad for Power supply for charge pump circuit.
    This pin should be disconnected when VPP is supplied externally
    7 NC No connection
    8 VSS Ground.
    9 VDD1 Power supply input: 1.65 - 3.5V
    10 IM0 These are the MPU interface mode select pads.
     808012C68004-wire SPI3-wire SPI
    IM0 0 0 0 0 1
    IM1 1 1 0 0 0
    IM2 1 0 1 0 0
    11 IM1
    12 IM2
    13 CSB This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
    14 RESB This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
    15 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
    A0 = “H”: the inputs at D0 to D7 are treated as display data.
    A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
    In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
    16 WRB This is a MPU interface input pad.
    When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
    When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
    When R/W = “H”: Read.
    When R/W = “L”: Write.
    17 RDB This is a MPU interface input pad.
    When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
    When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
    When RD = “H”: Enable.
    When RD = “L”: Disable.
    18 D0 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
    When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
    When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
    19 D1
    20 D2
    21 D3
    22 D4
    23 D5
    24 D6
    25 D7
    26 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
    27 VCOMH This is a pad for the voltage output high level for common signals.
    A capacitor should be connected between this pad and VSS.
    28 VPP OLED panel power supply. Generated by internal charge pump.
    Connect to capacitor. It could be supplied externally.
    29 NC No connection
    30 NC No connection

     

    General Specification

    ItemDimensionUnit
    Dot Matrix 128 x 64 -
    Module dimension 26.70 × 19.26 ×1.26 mm
    Active Area 21.74 × 10.86 mm
    Pixel Size 0.148 × 0.148 mm
    Pixel Pitch 0.170 × 0.170 mm
    Display Mode Passive Matrix
    Display Color Monochrome
    Drive Duty 1/64 Duty
    Controller IC SH1106
    Interface 6800, 8080, SPI, I2C
    Size 0.96 inch

     

    Absolute Maximum Ratings

    ParameterSymbolMinMaxUnit
    Supply Voltage for Logic VDD1 -0.3 3.6 V
    Power supply for charge pump circuit VDD2 -0.3 4.8 V
    Supply Voltage for Display VPP -0.3 14.5 V
    Operating Temperature TOP -40 +80 °C
    Storage Temperature TSTG -40 +85 °C

     

    Electronical Characteristics

    DC Electrical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage for Logic VDD1 - 2.8 3.0 3.3 V
    Power supply for charge pump circuit VDD2 - 3.5 3.8 4.2 V
    Charge Pump Output Voltage for Display
    (Generated by Internal DC/DC)
    Charge Pump
    VPP
    - 7.5 8 8.5 V
    High Level Input VIH - 0.8xVDD1 - VDD1 V
    Low Level Input VIL - VSS - 0.2xVDD1 V
    High Level Output VOH - 0.8xVDD1 - VDD1 V
    Low Level Output VOL - VSS - 0.2xVDD1 V
    Operating Current for VDD2 Display 50% ON IDD2 - - 10 16 mA

     

    FPC options

    FPC LengthPINPitchZIF FPC or HOTBAR FPCInterfaceFPC No.Create Date
    13 30 0.7 HOTBAR FPC 6800, 8080, 4-Wire SPI, I2C FPC2070003001XXXXX09 20180613
    40.95 30 0.5 ZIF  6800, 8080, SPI, I2C FPC2050003011XXXXX23 20190412


    Specifiche di prodotto
    Size 0.96"
    Resolution 128x64
    Active Area (mm) 21.74x10.86
    Dot Size 0.17x0.17
    Polarizer Anti-glare
    Color Sky Blue
    Power supply 3V
    Display Interface 6800/8080/SPI/I2C
    Display IC SH1106G
    Constructive Structure COG
    Frame No
    Touch Panel No touch
    O. Temperature (°C) -40~80
    Data Connection FPC for Soldering
    Pin Nr. 30
    Pin Pitch 0.7mm
    Preferred - Not Preferred Not Preferred
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni