Cerca
Italiano
Catalogo
    Menu Chiudi

    WL0F00101000JGDAESA02-FC

    TFT 10.1" 1024x600, RS485 ModBus interface & GPIO Support, 32MB Flash Memory, 400cd/m², Wide View Angle (IPS), Capacitive touch panel (GG)
    Brand: Winstar
    Cod.: WL0F00101000JGDAESA02-FC

    Kit accessori

    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    Prezzo
    €163,00
    €146,70
    €137,90

    Per quantità maggiori di 24pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Disponibile
    €163,00 IVA esclusa
    i h

    DESCRIPTION

        Link to 'SMART GUI BLIDER' INTRODUCTION & VIDEO

    WL0F00101000JGDAESA02-FC is a 10.1-inch Smart Display_RS485 series TFT module, designed as a slave device that communicates with a master device through RS485 commands to display content and return touch event data via Modbus protocol. It features WINSTAR’s TFT standard IPS wide-temperature display, WF101-1024600JL#0P8-FC, and a 4-layer FR4 PCBA with built-in firmware. This 10.1" RS485 series TFT provides an efficient solution for accelerating product development, leveraging the WINSTAR GUI Builder to minimize coding time and reduce overall development costs.

    Key Features:

    • +12V power input with an 8V to 28V dynamic range and a power consumption of approximately 6W.
    • Self-testing functionality upon boot-up.
    • RS485 communication interface with Modbus protocol support.
    • 32MB built-in flash memory for storing fonts and Object Dictionary Data.
    • Supports capacitive touch panel (CTP).
    • Embedded buzzer, controllable by the master device.
    • GPIO PIN support for extended functionality.
    • Design the UI without writing a line of code by WINSTARGUI builder! (►Link to GUI Builder Introduction)
    • Built on the STM32F series MCU, supporting STMicroelectronics' software development tools.
    • Extended memory management, including:
      • Up to 255 objects per page (vs. 64 in the 16MB version).
      • Up to 1000 total objects (vs. 500 in the 16MB version).
      • Support for up to 64 pages (vs. 30 in the 16MB version).
      • Dynamic memory allocation for efficient flash storage management.

     

    DRAWING

    SPECIFICATIONS

    General Specifications

    ItemStandard ValueUnit
    Operating voltage 8V~28V dynamic Vdc
    Communication Interface RS485 -
    MCU STM32F746 N/A
    Flash Memory 32 MB
    LCD display size 10.1 inch
    Dot Matrix 1024 x RGB x 600(TFT) dots
    Module dimension 248.8(W) x 143(H) x 23.2(D) mm
    Active area 222.72 (H) x 125.28(V) mm
    Pixel pitch 0.2175(W) x 0.2088(H) mm
    Brightness Min: 300; Typ: 400 cd/m2
    LCD type TFT, Normally Black, Transmissive
    View Direction 85/85/85/85
    Aspect Ratio 16:9
    Touch Panel With Projected Capacitive Touch Panel (PCAP)
    Surface Glare

     

    Absolute Maximum Ratings

    ItemSymbolMinTypMaxUnit
    Operating Temperature TOP -20 - +70 ℃
    Storage Temperature TST -30 - +80 ℃

     

    Electrical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage VCC - 8 12 28 V
    Supply LCM current I(mA) - - 550 - mA

     

    BOM

    ItemDescription
    LCM WF101-1024600JL#0P8-FC
    PCBA SV10010R100JC00N0108

     

    Interface Pin Function

    CON1 definition

    PinSymbolFunctionRemark
    1 VIN Power supply 8V to 28V input Input
    2 GND Power supply GND input Input
    3 NC - -
    4 NC - -
    5 GND Power supply GND input GND
    6 GND Power supply GND input GND
    7 Reserve USB_D- Reserve
    8 Reserve USB_D+ Reserve
    9 NC - -
    10 Reserve USART RX interface(Reserve) Reserve
    11 Reserve USART TX interface(Reserve) Reserve
    12 GND Power supply GND input GND
    13 VIN Power supply 8V to 28V input Input
    14 485B RS485 D- I/O
    15 485A RS485 D+ I/O
    16 GND Power supply GND input Input


    CON2 definition

    PinSymbolFunctionRemark
    1 +3V3 3.3V power for JTAG interface Output
    2 SWCLK CLK pin for JTAG interface Input
    3 GND GND for JTAG interface Output
    4 SWDIO Data pin for JTAG interface I/O
    5 NRST Reset pin for JTAG interface Input
    6 GND GND Output
    7 IO_8 IO_8 for system Resume
    from suspend (Reserve)
    WKup,ADC,Timer,Event,I/O
    8 REST Reset (active Low) (Reserve) I
    9 IO_0 ADC,DAC,Timer,Event,I/O PA5
    10 IO_1 ADC,Timer,Event,I/O PA6
    11 IO_2 ADC,Timer,Event,I/O PA7
    12 IO_3 RST,Timer,Event,I/O PA8
    13 IO_4 RST,Timer,Event,I/O PC13
    14 IO_5 ADC,Timer,Event,I/O PB11
    15 IO_6 RST,Timer,Event,I/O PA15
    16 IO_7 RST,ADC,Event,I/O PD11
     

    Display Usage

    Functional description

    Smart Display can be used to display the coordinate, status and data information provided by the connected HOST device. Customers can configure the position coordinates they want to display in normal operation mode

    The Display is designed to be easily connected to a controller network, and to use the register type of Holding Register.


    Splash Screen

    The default splash image is shown below.

    This product is produced as a generic product. If you require a custom splash image for your application, contact us to discuss

    Default Selection

    Press the preferred application and hold for 3 seconds for the first time power on.

    Winstar's Smart Display Default Selection

    Acquisition of Displayed Data

    Smart Display uses the Modbus protocol to get and send the data.

    On Config mode, customers can set the coordinates or type of objects; On Display mode, customers can send and get data of objects.

    Configuring the Display

    Winstar Smart Display RS-485 series offers an out-of-the-box Modbus development experience that will lower customers' development costs and speed time-to-market expectations.

    The Smart Display can use wide-temperature are designed to support control applications in harsh operating conditions, which designed to be connected to a variety of different situation combinations, such as automotive, marine, power generation and oil-and-gas.

    The Smart Display comes with standard UI objects to get customers project off the ground quickly. If customers need custom UI objects support, our engineers are here to help. Send over your contents in PNG/JPG format, we will send over a new set of UI objects within 3~5 working days.

    The Smart Display is defined as a slave device, which is controlled by master device via RS-485 command to render display content on the display screen and return touch event data with protocol objects.

    Example Screen Layout (Industry application)

    Example Layout

    The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in an industry application situation.

     

    Example Layout (Vehicle automotive)

    The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in a vehicle automotive situation.

     

    Example Layout (Medical application)

    The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in a Medical application situation.

     

    EVALUATION KIT 

    Evaluation Kit P/N WWSSDEMO101J-DA-11#004 available at the links:

    ITA: https://www.first-components.com/it/wwssdemo101j-da-11004

    ENG: https://www.first-components.com/en/wwssdemo101j-da-11004

    Specifiche di prodotto
    Size 10.1"
    Resolution 1024x600
    Active Area (mm) 222.72x125.28
    Color Full Color
    Power supply 12V
    Display Interface RS485 + GPIO
    View Angle IPS
    Frame Yes
    Touch Panel Capacitive
    O. Temperature (°C) -20~70
    Preferred - Not Preferred Preferred
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni