Cerca
Italiano
Catalogo
    Menu Chiudi

    WEO16080W#AP3N00000-FC

    PMOLED 1.54" Graphic 160x80, White color, COG, 3V, Interface 6800,8080,SPI, I2C, Glare
    Brand: Winstar
    Cod.: WEO16080W#AP3N00000-FC

    Kit accessori

    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    25+
    Prezzo
    €10,70
    €9,60
    €9,10
    €8,90

    Per quantità maggiori di 49pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Disponibile
    €10,70 IVA esclusa
    i h

    DESCRIPTION

    WEO16080W#AP3N00000-FC is a 1.54-inch COG graphic OLED display featuring a resolution of 160x80 dots. It measures 43.5 x 22.5 mm with an active area of 35.02 x 17.50 mm, and its slim profile of 1.41 mm is attributed to its COG structure.

    Equipped with the SSD1320 IC, this module supports 6800/8080 8-bit, 4-wire SPI, and I2C interfaces. It offers 4-bit (16 Levels) grayscale and achieves an impressive contrast ratio of 10,000:1.

    Operable with a logic power supply voltage ranging from 1.65V to 3.3V (typically 3.0V), the module operates reliably in temperatures from -40°C to +80°C, with a storage capability from -40°C to +85°C.

    Ideal for a variety of applications including Networking Products, USB Testers, Smart Watches, Gaming Keyboards, and Smart Healthcare Devices such as oximeters and skin analyzers, WEO16080W#AP3N00000-FC enhances display quality with its crisp and vibrant screen.

    With its high resolution (160x80 pixels) and low power consumption, this OLED display module is perfectly suited for performance-driven and efficient applications.

     

    DRAWING

     

    SPECIFICATIONS

    Interface Pin Function

    No.SymbolFunction
    1 N.C.
    (GND)
    Reserved Pin (Supporting Pin)
    The supporting pin can reduce the influences from stresses on the function pins.
    This pin could be connected to external ground as the ESD protection circuit.
    2 VCC Power Supply for OEL Panel
    This is the most positive voltage supply pin of the chip. It must be connected to external source.
    3~4 N.C. Reserved Pin
    The N.C. pin between function pins are reserved for compatible and flexible design.
    5 BS1 Communicating Protocol Select
    These pins are MCU interface selection input. See the following table:
     BS1BS2
    I2C 1 0
    4-wire SPI 0 0
    8-bit 68XX Parallel 0 1
    8-bit 80XX Parallel 1 1
    6 BS2
    7 VSS Ground of Logic Circuit
    This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground.
    8 IREF Current Reference for Brightness Adjustment
    This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current at 10μA maximum.
    9 CS# Chip Select
    This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
    10 RES# Power Reset for Controller and Driver
    This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin pull high during normal operation.
    11 D/C# Data/Command Control
    This pin is Data/Command control pin. When the pin is pulled high, the input at
    D7~D0 is treated as display data. When the pin is pulled low, the input at
    D7~D0 will be transferred to the command register.
    In I2C mode, this pin acts as SA0 for slave address selection.
    12 R/W# Read/Write Select or Write
    This pin is MCU interface input.
    When interfacing to a 68XX-series microprocessor, this pin will be used as
    Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
    When 80XX interface mode is selected, this pin will be the Write (WR#) input.
    Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
    When serial mode is selected, this pin must be connected to VSS.
    13 E/RD# Read/Write Enable or Read
    This pin is MCU interface input.
    When interfacing to a 68XX-series microprocessor, this pin will be used as the
    Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
    When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
    When serial mode is selected, this pin must be connected to VSS.
    14 D0 Host Data Input/Output Bus
    These pins are bi-directional data bus connecting to the MCU data bus.
    Unused pins are recommended to tie LOW.
    When serial interface mode is selected, D2, D1 should be tied together as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
    When I2C mode is selected, D2, D1 should be tied together and serve as SDAout,
    SDAin in application and D0 is the serial clock input, SCL.
    15 D1
    16 D2
    17 D3
    18 D4
    19 D5
    20 D6
    21 D7
    22 VDD Power Supply for Logic
    This is a voltage supply pin. It must be connected to external source.
    23 VCOMH Voltage Output High Level for COM Signal
    This pin is the input pin for the voltage output high level for COM signals. A tantalum capacitor should be connected between this pin and VSS.
    24 VCC Power Supply for OEL Panel
    This is the most positive voltage supply pin of the chip. It must be connected to external source.

     

    Mechanical Data

    ItemDimensionUnit
    Dot Matrix 160 x 80 Dots -
    Module dimension 43.5 x 22.5 x 1.41 mm
    Active Area 35.02 x 17.50 mm
    Pixel Size 0.199 x 0.199 mm
    Pixel Pitch 0.219 x 0.219 mm
    Display Mode Passive Matrix
    Display Color White
    Drive Duty 1/80 Duty
    Gray Scale 4 bits
    Interface 6800,8080,4-Wire SPI,I2C
    IC SSD1320
    Size 1.54 inch

     

    Absolute Maximum Ratings

    ParameterSymbolMinTyp.MaxUnit
    Supply Voltage for Logic VDD -0.3 - 4 V
    Supply Voltage for Display VCC 0 - 19 V
    Operating Temperature TOP -40 - +80 °C
    Storage Temperature TSTG -40 - +85 °C

     

    Electronical Characteristics

    DC Electrical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage for Logic VDD - 1.65 3.0 3.3 V
    Supply Voltage for Display VCC - 8.0 15.0 15.5 V
    High Level Input VIH - 0.8×VDD - VDD V
    Low Level Input VIL - 0 - 0.2×VDD V
    High Level Output VOH - 0.9×VDD - VDD V
    Low Level Output VOL - 0 - 0.1×VDD V
    VCC Supply Current ICC VDD=3V,VCC=15V
    Display 50% Pixel ON
    - 14 21 mA
    Specifiche di prodotto
    Size 1.54"
    Resolution 160x80
    Active Area (mm) 35.02x17.50
    Dot Size 0.19x0.19
    Polarizer Glare
    Color White
    Power supply 3V
    Display Interface 6800/8080/SPI/I2C
    Display IC SSD1320
    Constructive Structure COG
    Frame No
    Touch Panel No touch
    O. Temperature (°C) -40~80
    Data Connection FPC for ZIF Connector
    Pin Nr. 24
    Pin Pitch 0.5mm
    Preferred - Not Preferred Preferred
    You are running a Trial version of Nop Attachments
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni