Cerca
Italiano
Catalogo
    Menu Chiudi
    PMOLED 0.96" Graphic 128x64, Yellow color, COG, 3V, Interface 6800,8080,SPI,I2C, SSD1306BZ IC, Glare (FPC for ZIF Connector)
    Brand: Winstar
    Cod.: WEO12864L#D28-FC
    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    25+
    Prezzo
    €8,40
    €7,60
    €7,10
    €6,90

    Per quantità maggiori di 49pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Il prodotto non può essere aggiunto al carrello. Prego verificare con FC la futura disponibilità
    €8,40 IVA esclusa
    i h

    DESCRIPTION

    Winstar released a 0.96 inch Thin OLED Display WEO12864L#D28-FC model which is made of 128x64 pixels: the new version is 1.26 mm on thickness. The new version thin 0.96" OLED display is also built-in SSD1306 driver IC; it communicates via 6800/8080 8-bit parallel and I2C/SPI interface (0.96" OLED I2C). 

     

    DRAWING

    Square LCD Screen, Square Screen TFT, ST7789T3-G4-1 - WF0154ATAAA4DSN0
     

     

    SPECIFICATIONS

    Interface Pin Function

    No.SymbolFunction
    1 N.C. (GND) Reserved Pin (Supporting Pin)
    The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
    2 C2N Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
    3 C2P
    4 C1P
    5 C1N
    6 VBAT Power Supply for DC/DC Converter Circuit
    This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
    7 NC NC
    8 VSS Ground of Logic Circuit
    This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
    9 VDD Power Supply for Logic
    This is a voltage supply pin. It must be connected to external source.
    10 BS0 Communicating Protocol Select
    These pins are MCU interface selection input. See the
    following table:
    11 BS1
    12 BS2
    13 CS# Chip Select
    This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low.
    14 RES# Power Reset for Controller and Driver
    This pin is reset signal input. When the pin is low, initialization of the chip is executed.
    15 D/C# Data/Command Control
    This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data.
    When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams.
    When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection.
    16 R/W# Read/Write Select or Write
    This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode.
    When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low.
    17 E/RD# Read/Write Enable or Read
    This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
    When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low.
    18~25 D0~D7 Host Data Input/Output Bus
    These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.
    26 IREF Current Reference for Brightness Adjustment
    This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
    27 VCOMH Voltage Output High Level for COM Signal
    This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
    28 VCC Power Supply for OEL Panel
    This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.
    29 VLSS Ground of Analog Circuit
    This is an analog ground pin. It should be connected to VSS externally.
    30 NC
    (GND)
    Reserved Pin (Supporting Pin)
    The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

     

    Mechanical Data

    ItemDimensionsUnit
    Dot Matrix 128 × 64 Dots
    Module dimension 26.7 × 19.26 × 1.26 mm
    Active area 21.738 × 10.858 mm
    Dot size 0.148 × 0.148 mm
    Dot pitch 0.17 × 0.17 mm
    Display Mode Passive Matrix
    Display Color Yellow
    Drive Duty 1/64 Duty
    IC SSD1306
    Interface 6800,8080,SPI,I2C
    Size 0.96 inch

     

    Absolute Maximum Ratings

    ParameterSymbolMinMaxUnit
    Supply Voltage for Logic VDD 0 4.0 V
    Supply Voltage for Display VCC 0 15.0 V
    Operating Temperature TOP -40 +80 °C
    Storage Temperature TSTG -40 +85 °C

     

    Electronical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage for Logic VDD - 2.8 3.0 3.3 V
    Supply Voltage for Display VCC - 11.5 12.0 12.5 V
    Input High Volt. VIH - 0.8×VDD - VDDIO V
    Input Low Volt. VIL - 0 - 0.2×VDD V
    Output High Volt. VOH - 0.9×VDD - VDDIO V
    Output Low Volt. VOL - 0 - 0.1×VDD V
    Operating Current for VCC (50% display ON) ICC - - 16.0 20.0 mA
    Specifiche di prodotto
    Size 0.96"
    Resolution 128x64
    Active Area (mm) 21.73x10.85
    Dot Size 0.14x0.14
    Polarizer Glare
    Color Yellow
    Power supply 3V
    Display Interface 6800/8080/SPI/I2C
    Display IC SSD1306Z
    Constructive Structure COG
    Frame No
    Touch Panel No touch
    O. Temperature (°C) -40~80
    Data Connection FPC for ZIF Connector
    Pin Nr. 30
    Pin Pitch 0.5mm
    Preferred - Not Preferred Preferred
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni