Cerca
Italiano
Catalogo
    Menu Chiudi

    WEO12832W#MA3J00000-FC

    PMOLED 0.91" Graphic 128x32, White color, COG, 3V, Interface SPI,I2C (FPC per ZIF), SSD7317 IC, Glare, In-Cell Touch Panel TDDI (Touch with Display Driver IC)
    Brand: Winstar
    Cod.: WEO12832W#MA3J00000-FC

    Kit accessori

    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    25+
    Prezzo
    €9,80
    €8,90
    €8,30
    €8,10

    Per quantità maggiori di 49pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Il prodotto non può essere aggiunto al carrello. Prego verificare con FC la futura disponibilità
    €9,80 IVA esclusa
    i h

    DESCRIPTION

    0.91” COG Graphic OLED display with In-Cell Capacitive Touch Panel, which is made of resolution 128x64 pixels. This module is built-in with SSD7317 TDDI IC (Touch with Display Driver IC); it supports 4-Wire SPI and I2C interface. This SSD7317 IC is a Touch and Display Driver Integration IC (TDDI IC), which integrates touch and display microelectronics into a single chip for use on PMOLED panels, targeting applications including wearables, smart home appliances, and smart healthcare devices. 

    This model adopted In-Cell Touch Panel technology, which supports SPI and I2C interface featuring four touch keys (areas) and one direction slide (supports right or left direction). The supply voltage for logic (VDD) is from 3.0V to 3.5V, typical value 3.3V, 1/32 driving duty, the display with 50% Checkboard current is 4mA @8.5V VCC (typical value), driving duty 1/32. This module can be operating at temperatures from -40℃ to 80℃; its storage temperatures range from -40℃ to 85℃.

     

    DRAWING

    SPECIFICATIONS

     

    Interface Pin Function

    No.SymbolFunction
    1 VCI Power supply pin for touch analog driving. VCI must be greater than or equal to VDD.
    2 VSS Ground pin.
    3 VCC Power Supply for Display. Most positive voltage. Connect to external source.
    4 VSL This is segment voltage (output low level) reference pin.
    When external VSL is not used, connect externally to VSS. When external VSL is used, connect with resistor and diode to ground
    5 DCDCEN0 Enable output pin for external DCDC circuit. NC if not used
    6 DCDCEN1 Enable input pin for external DCDC circuit. Tie low if not used.
    7 VDD Power supply pin for core logic operation.
    8 FR This pin outputs RAM write synchronization signal.
    It should be kept NC if it is not used.
    9 DCS This pin is the chip select input connecting to the MCU for display interface.
    10 TCS This pin is the chip select input connecting to the MCU for touch.
    11 RES# This pin is the reset signal input for display interface.
    12 TRES This pin is the reset signal input for touch.
    13 DC This pin is Data/Command control pin for display interface.
    In I2C mode, this pin acts as SA0 for slave address selection.
    14 E/RD# In I2C mode, this pin acts as SA1 for slave address selection.
    15 IRQ Interrupt signal for touch reporting.
    16 TD0 Serial Data Input/Output and clock for Touch
    In SPI mode TD2 serves as SDOUT, TD1 serves as SDIN, and TD0 serves as the serial clock SCLK.
    In I2C mode TD2 and TD1 should be tied together and serve as SDA and TD0 is the serial clock SCL. External pull up resistors.
    17 TD1
    18 TD2
    19 VSS Ground pin.
    20 D0 The serial clock input for display interface.
    21 D1 The serial data input for display interface.
    22 BS1
    BS1BS3Display InterfaceTouch Interface
    0 0 4 -SPI SPI
    0 1 4-SPI I2C
    1 0 I2C SPI
    1 1 I2C I2C
    23 BS3
    24 VCOMH COM signal deselected voltage level.
    A capacitor should be connected between this pin and VSS.

     

    Mechanical Data

    ItemDimensionUnit
    Dot Matrix 128 × 32 Dots -
    Module dimension 30.0 × 11.5 × 1.41 mm
    Active Area 22.38 × 5.58 mm
    Pixel Size 0.155 × 0.155 mm
    Pixel Pitch 0.175 × 0.175 mm
    Display Mode Passive Matrix
    Display Color Monochrome
    Drive Duty 1/32 Duty
    IC SSD7317
    OLED Interface 4-wire SPI,I2C
    CTP Interface SPI,I2C
    Gesture 4-key and 1-D slide
    Size 0.91 inch

     

    Absolute Maximum Ratings

    ParameterSymbolMinMaxUnit
    Supply Voltage for Logic VDD 0 4 V
    Supply Voltage for Display VCC 0 19 V
    Operating Temperature TOP -40 80 °C
    Storage Temperature TSTG -40 85 °C
     

     

    Electrical Characteristics

    DC Electrical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage for Logic VDD - 3.0 3.3 3.5 V
    Touch controller Supply Voltage VCI - 3.0 - 3.5 V
    Supply Voltage for Display VCC - 8.0 8.5 9.0 V
    Input High Volt. VIH - 0.8×VDD - - V
    Input Low Volt. VIL - - - 0.2×VDD V
    Output High Volt. VOH - 0.9×VDD - - V
    Output Low Volt. VOL - - - 0.1×VDD V
    50% Check Board
    operating Current
    ICC VCC =8.5V - 4 8 mA



    Specifiche di prodotto
    Size 0.91"
    Resolution 128x32
    Active Area (mm) 22.38x5.58
    Dot Size 0.15x0.15
    Polarizer Glare
    Color White
    Power supply 3V
    Display Interface SPI/I2C
    Display IC SSD7317
    Constructive Structure COG
    Frame No
    Touch Panel In-Cell CTP
    O. Temperature (°C) -40~80
    Data Connection FPC for ZIF Connector
    Pin Nr. 24
    Pin Pitch 0.5mm
    Preferred - Not Preferred Preferred
    You are running a Trial version of Nop Attachments
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni