Cerca
Italiano
Catalogo
    Menu Chiudi
    PMOLED 2.08" Graphic 256x64, White, COG + Small PCB, 3~5V, Interface SPI, Anti-glare
    Brand: Winstar
    Cod.: WEA25664W#A01-FC
    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    25+
    Prezzo
    €17,70
    €15,90
    €14,90
    €14,60

    Per quantità maggiori di 49pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Disponibile
    €17,70 IVA esclusa
    i h

    DESCRIPTION

    Graphic COG with PCB OLED display model, which is made of 256x64 pixels, diagonal size 2.08 inch. It is built in with SSD1362 driver IC; it supports 4-Wire SPI interface, 4 bits grayscale image, 1/64 duty cycle. It has PCB outline size 70.0 x 22.0 mm with mounting holes on board and 7x1 metal pins on module.

    It is supported by 3V ~5V, within DC-DC conversion circuit, display with 50% check board current is 90mA@3Vdd (typical value), 1/64 duty cycle. Operating temperatures from -40℃ to +80℃; its storage temperatures range from -40℃ to +85℃.

     

    DRAWING

    OLED Graphic COG+PCB, 256x64, 2.08 - WEA025664A - Winstar Display

    SPECIFICATIONS

     

    Interface Pin Function

    No.SymbolFunction
    1 GND Reserved pin. It should be connected to ground.
    2 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin. It is supplied by external high voltage source.
    3 D0 These pins are bi-directional data bus connecting to the MCU data bus.
    Unused pins are recommended to tie LOW.
    When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SID.
    4 D1
    5 RES# This pin is reset signal input.
    When the pin is pulled LOW, initialization of the chip is executed.
    Keep this pin pull HIGH during normal operation.
    6 D/C# This pin is Data/Command control pin connecting to the MCU.
    When the pin is pulled HIGH, the data at D[1:0] will be interpreted as data.
    When the pin is pulled LOW, the data at D[1:0] will be transferred to a command register.
    7 CS# This pin is the chip select input connecting to the MCU.
    The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).

     

    Mechanical Data

    ItemDimensionUnit
    Dot Matrix 256 x 64 Dots -
    Module dimension 70.0 x 22.0 x 1.71 mm
    Active Area 51.18 x 12.78 mm
    Pixel Size 0.18 x 0.18 mm
    Pixel Pitch 0.2 x 0.2 mm
    Display Mode Passive Matrix
    Display Color Monochrome
    Drive Duty 1/64 Duty
    Gray Scale 4 Bits
    IC SSD1362
    Interface SPI
    Size 2.08 inch

     

    Absolute Maximum Ratings

    ParameterSymbolMinMaxUnit
    Supply Voltage VCC 1.65 5.5 V
    Operating Temperature TOP -40 +80 °C
    Storage Temperature TSTG -40 +85 °C

     

    Electronical Characteristics

    DC Electrical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage VCC - 2.8 3.3 5.2 V
    Input High Volt. VIH - 0.8×VCC - VCC V
    Input Low Volt. VIL - 0 - 0.2×VCC V
    Output High Volt. VOH - 0.9×VCC - VCC V
    Output Low Volt. VOL - 0 - 0.1×VCC V
    50% Check Board operating Current ICC VCC=3.3V - 90 135 mA


    Specifiche di prodotto
    Size 2.08"
    Resolution 256x64
    Active Area (mm) 51.18x12.78
    Dot Size 0.18x0.18
    Polarizer Anti-glare
    Color White
    Power supply 3~5V
    Display Interface SPI
    Display IC SSD1362
    Constructive Structure COG + PCB
    Frame Yes
    Touch Panel No touch
    O. Temperature (°C) -40~80
    Data Connection Pin Strip
    Pin Nr. 7
    Pin Pitch 2.54mm
    Preferred - Not Preferred Preferred
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni